KNX Three phase energy meter

Active energy meter for three phase alternating with a backlight LCD display for displaying the values, an input for switching rates between 2 rates and direct connection to 63 A. The values of instantaneous power, KW / KVA h and scored for rate 1 and 2, are sent via the supplied KNX bus interface.

DOWNLOAD Data sheet - Satelco Article number 10286

 

Presence sensor is a KNX occupancy detector with integrated function of motion detection and light evaluation. Up to four different operating modes are possible:
the first is standard semi-automatic or fully automatic mode (switching), the second is a semi-automatic or fully automatic mode with the constant adjustment of brightness (dimming), the third is the slave mode and the fourth is permanent adjustment of the light (control of light is not dependent on presence).
Two target values are set (specified in Lux) and a reference value remains fixed (specified in %). The values can be modified using a communication object. Soft Start for passing information to light setting. Reflectivity for a better adjustment to environmental conditions. HVAC channels activated by push button.

Motion detection:
The Presence Detector is based on a passive, heat-sensing infrared system, which registers heat movements.

Light evaluation:
The Presence Detector measures the light value ( inlux) and provides data to the KNX bus; this value can then be used to switch lights on when the occupancy detector detects motion and the light value is below a target value. This data can also be used to set a dimming value to a dimmer in order to mantain a target light value.

DOWNLOAD Data sheet - Satelco Article number 10657

 

KNX Dimmer Module 3 OUT / 1-10V

Dimmer used to control lighting circuits via a 1/10 V connection, acting upon remote control dimmers or electronic ballasts. Device is intended to be installed on DIN rail.

DOWNLOAD Data sheet - Satelco Article number 10279
 

KNX Dimmer Module 3x 300 W

The 3 channel Dimmer Module is designed to drive dimmerable lighting with KNX bus and allow dimming of incandescent and halogen loads of 230V, BT and TBT. The product can control one (900W), two (600+300W) or three (3x 300W) independent lighting circuits. Devise is intended to be installed on DIN rail.

DOWNLOAD Data sheet - Satelco Article number
 

KNX Inwall Module 8 IN / 4 OUT LED

This KNX module includes 4 digital inputs to interface free pontential contacts; 4 analog / 4 digital inputs for free potential contacts or temperature sensors and 4 led outputs. Digital inputs can interface sensors, traditional buttons etc.; 4 low voltage/current output channels to drive LED signal indicator lamps. Inputs 5 to 8, set as analog inputs, enable up to 2 temperature probes (with On/Off threshold) an 2 thermostats to control heating an cooling equipments, valves, 2 and 4 pipes fan coils.

DOWNLOAD Data sheet - Satelco Article number 10282
 

KNX Push Button Interface - 2 IN / 2 OUT LED - 4 IN / 4 OUT LED

The product is dedicated to interface of clean contacts with 2 or 4 input channels, such as sensors, traditional buttons and 2 or 4 low voltage/current output channels to drive LED signal indicator lamps.

DOWNLOAD Data sheet - Satelco Article no. 10280 + 10281
 

KNX Universal Module 4 OUT

The DIN Rail 4 Output Module is an EIB/KNX DIN rail mounting device useful to interface loads (e.g. lamps) for any kind of applications.
Device 4 outputs on board can be configured:
- Each output can be configured independently for load control
  (R1 to R4)
- Each output can be configured independently for ON / OFF or continuous switching
  (PWM) for Electric valves (solenoid actuators) (EV1 to EV4)
- Outputs can be configured in pairs for the management of roller shutters and blinds;
  up to 2 channels (A to B)
- Outputs can be configured in pairs for management of Motor Reductor or for solenoid
  valves with 3-point control or for ventilating grille; up to 2 channels (A to B)

DOWNLOAD Data sheet - Satelco Article number 10274
 

KNX Universal Module 8 OUT

The DIN rail 8 Output Module is an EIB/KNX DIN rail mounting device useful to Interface loads (e.g. lamps) for any kind of applications.
Device 8 outputs on board can be configured:
- Each output can be configured independently for load control
  (R1 to R8)
- Each output can be configured independently for ON / OFF or continuous switching
  (PWM) for Electric valves (solenoid actuators) (EV1 to EV8)
- Outputs can be configured in pairs for the management of roller shutters and blinds;
  up to 4 channels (A to D)
- Outputs can be configured in pairs for management of Motor Reductor or for solenoid
  valves with 3-point control or for ventilating grille; up to 4 channels (A to D)
- Fan Coil Actuator for 2/4 pipes systems for Heating / Cooling with 3 speed motors)
  (uses relay from 1 to 5)
- Device is intended to be installed on DIN rail.

DOWNLOAD Data sheet - Satelco Article number 10275
 

KNX Universal Module 12 OUT

The device is a DIN Rail 12 output 16A actuator and can be used to:
- Control up to 12 independent loads / lights
- Control up to 6 independent blind / roller shutters with mechanical
  end position

DOWNLOAD Data sheet - Satelco Article number 10276
 

KNX Universal Module 4 IN / 4 OUT C-Load

The DIN rail Module is an EIB/KNX DIN rail mounting device useful to interface commands (e.g. push buttons) or loads (e.g. lamps) for any kind of applications.
The device is equipped with 4 binary inputs (clean contacts) and 4 relay outputs suitable for capacitive loads. Inputs can be configured to conventional switching devices, e.g. push buttons, switches, floating contacts, for switching functions with pulse edge evaluation (e.g. rising or falling edge, toggle, etc. …). Inputs can be configured as output channels to drive LED synoptic monitoring panels. Inputs can be used as switch, dimming, shutter control, scenarios; outputs include switching function, scenarios, logic functions.
Outputs can act as interlocked channels; this function may be used to drive fan coils with 2-pipes / 3 speeds of 4-pipes / 2 speeds. Devices are intended to be installed on DIN rail.

DOWNLOAD Data sheet - Satelco Article number 10270
 

KNX Universal Module 8 IN / 8 Out - C-Load

The DIN rail Module is an EIB/KNX DIN rail mounting device useful to interface commands (e.g. push buttons) or loads (e.g. lamps) for any kind of applications.
The device is equipped with 8 binary inputs (potential free) and 8 relay outputs. Inputs can be connected to conventional switching devices, e.g. push buttons, switches, floating contacts, for switching functions with pulse edge evaluation (e.g. rising or falling edge, toggle, etc.). Inputs can be configured with ETS, as output channels to drive LEDs in synoptic monitoring panels. Inputs can be used to for switch, dimming, shutter control, scenarios; outputs include switching function, scenarios, logic functions.
Relay from 5 to 8 are equipped with manual command and can be switched manually.
 

DOWNLOAD Data sheet - Satelco Article number 10272
 

KNX Universal Module 4 IN / 4 OUT

The DIN rail 4 IN / 4 OUT Module (IO44E01KNX) is an EIB/KNX DIN rail mounting device useful to interface commands (e.g. push buttons) or loads (e.g.lamps) for any kind of applications. The device is equipped with 4 binary inputs (potential free) and 4 binary relay outputs. Inputs can be connected to conventional switching devices, e.g. push buttons, switches, floating contacts, for switching functions with pulse edge evaluation (e.g. rising or falling edge, toggle...). Inputs can be configured with ETS SW, as output to drive Leds. Inputs can be used to for on/off commands, dimming, shutter control, scene recall and control; outputs include switching function, scene recall and control logic function.

Device 4 outputs on board can be configured:
- Each output can be configured independently for load control (R1 to R4)
- Each output can be configured independently for ON / OFF or continuous switching (PWM)
  for Electric valves (solenoid actuators) (EV1 to EV4)
- Outputs can be configured in pairs for the management of roller shutters and blinds; up to 2 channels
  (A to B)
- Outputs can be configured in pairs for Management of Motor Reductor or for solenoid valves with 3-point
  control or for ventilating grille; up to 2 channels (A to B)

Satelco Article number 10271
 

KNX Universal Module 8 IN / 8 OUT

The DIN rail  8 IN / 8 OUT Module (IO88E01KNX) is an EIB/KNX DIN rail mounting device useful to interface commands (e.g. push buttons) or loads (e.g. lamps) for any kind of applications. The device is equipped with 8 binary inputs (potential free) and 8 binary relay outputs. Inputs can be connected to conventional switching devices, e.g. push buttons, switches, floating contacts, for switching functions with pulse edge evaluation (e.g. rising or falling edge, toggle...). Inputs can be configured with ETS SW, as output to drive Leds. Inputs can be used to for on/off commands, dimming, shutter control, scene recall and control; outputs include switching function, scene recall and control logic function.

Device 8 outputs on board can be configured:
- Each output can be configured independently for load control (R1 to R8)
- Each output can be configured independently for ON / OFF or continuous switching (PWM) for Electric
  valves (solenoid actuators) (EV1 to EV8)
- Outputs can be configured in pairs for the management of roller shutters and blinds; up to 4 channels
  (A to D)
- Outputs can be configured in pairs for management of Motor Reductor or for solenoid valves with 3-point
  control or for ventilating grille; up to 4 channels (A to D)
- Fan Coil Actuator for 2/4 pipes systems for Heating / Cooling with 3 speed motors)
  (uses relay from 1 to 5)

Satelco Article number 10273